Ositech comm Trumpcard Data/Fax Modem Bedienungsanleitung Seite 61
- Seite / 86
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
User’s Guide and Reference 4 - 29
Modem Command Reference
\Nn — Operation Mode Control
Parameters 0, 1, 2, 3, 4, or 5
Default 3
Selects the operating mode the modem uses while connected (see &Qn
command).
Examples
AT\N0 Selects Normal (speed buffering) mode. This option
takes effect at physical connection time.
AT\N1 Same as AT\N0.
AT\N2 Selects reliable link mode. This defines the modem-
to-modem connection to require error correction
connection. If an attempt to establish the reliable
link fails, the modem disconnects.
AT\N3 Selects auto-reliable link mode. The modem will
attempt an error-correction connection but will
fallback to Normal mode if unable to establish an
error correcting connection. This command takes
effect at physical connection time only.
AT\N4 Selects LAPM error-correction mode. The modem
will attempt a LAPM error-correction connection. If
the attempt fails, the modem disconnects.
AT\N5 Selects MNP error-correction mode. The modem will
attempt a MNP error-correction connection. If the
attempt fails, the modem disconnects.
%Cn — Compression Control
Parameters: 0, 1, 2, or 3
Default 3
Enables or disables data compression negotiation. The modem can only
perform data compression on an error-correcting link.
Examples
AT%C0 Disables data compression
AT%C1 Enables MNP 5 data compression
AT%C2 Enables V.42bis data compression
AT%C3 Enables both MNP 5 and V.42bis data compression
- Trumpcard Data/Fax Modem 1
- User’s Guide and Reference 1
- Copyright 2
- How To Contact Us 2
- Contents 8
- Modem Command Reference 4-1 9
- Modem Test Procedures 5-1 9
- Introduction 11
- Features 12
- Facsimile Mode 13
- Cellular Mode 13
- Unique Features 14
- Industry Standards 15
- Section One 16
- Hardware Installation 17
- Preparing for Installation 17
- Installing the Trumpcard 18
- Section Two 20
- Basic Modem Operation 21
- Before You Begin 22
- Operating the 23
- Making an Outgoing Call 24
- Re-Dialling the Last Number 25
- Storing a Number 25
- Connection Messages 25
- Section Four 26
- Ending Your Connection 27
- Connection 27
- Receiving an Incoming Call 28
- Cellular Phone Configuration 30
- Outgoing Cellular Call 30
- Incoming Cellular Call 30
- Cellular Call Status 31
- Modem Command Reference 33
- Modem Command Guidelines 34
- Modem Command Summary 36
- Modem Command Descriptions 38
- Bn — Set ITU-T or Bell Mode 39
- Dn — Dial 39
- Examples 40
- En — Command Echo 41
- Sub-parameter Definitions 42
- Hn — Switch-Hook Control 43
- In — Identification 44
- Ln — Speaker Volume 44
- Mn — Speaker Control 44
- Nn — Automode Detection 45
- P — Set Pulse Dial as Default 46
- Qn — Result Code Display 46
- Sn — Read/Write S Registers 46
- T — Set Tone Dial as Default 47
- Vn — Result Code Form 47
- Wn — Connect Message Control 47
- Xn — Extended Result Codes 48
- Section Four 50
- Zn — Reset 51
- &Cn — DCD Option 51
- &Dn — DTR Option 52
- &Gn — Set Guard Tone 53
- &Ln — Line Type 54
- &Mn — Communication Mode 54
- &Qn — Communication Mode 54
- &Rn — RTS/CTS Option 55
- &Sn — DSR Option 55
- &Tn — Test and Diagnostic 56
- &Wn — Store User Profile 58
- \Bn — Transmit Break 59
- \Kn — Break Control 59
- \Nn — Operation Mode Control 61
- %Cn — Compression Control 61
- -Kn — MNP Extended Services 63
- *Hn — Link Negotiation Speed 63
- :En — Compromise Equalizer 64
- Modem S Registers 66
- Modem Register Summary 66
- Register Descriptions 69
- S5 — Backspace Character 70
- S11 — DTMF Tone Duration 71
- S12 — Escape Code Guard Time 71
- S18 — Test Timer 72
- S24 — Sleep Inactivity Timer 72
- S25 — Delay to DTR 72
- S30 — Inactivity Timer 72
- S32 — XON Character 73
- S33 — XOFF Character 73
- S36 — LAPM Failure Control 73
- S46 — Protocol Selection 75
- S48 — V.42 Negotiation Action 76
- S95 — Extended Result Codes 77
- Facsimile Commands 78
- Modem Test Procedures 79
- Local Modem Self-Test 80
- Local Analog Loopback 81
- Generated Pattern 82
- Remote Digital Loopback 83
- Local Digital Loopback 85
- Testing Modem Memory 86
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern